Connect both hard drive and SSD to Mac computer and launch EaseUS Mac cloning software. Follow the detailed guide and get started. Only several simple clicks can help accomplish the job of cloning Mac hard drive to a solid state drive.
2017 Best Ssd Cloner Install An SSDThe MacBook Pro doesn’t have space for a second drive by default, but because it has an optical drive (and most people hardly use them anyway) this can be removed to make way for the new SSD.Clonezilla is the best and the most free disk Cloning Software For Mac. Since the vast majority of Mac sales are MacBooks, this article describes the basics of installing an additional SSD in your MacBook. Many of the iMac desktops have quite a lot of spare room inside, so it’s possible to install an SSD as a secondary disk drive – this way Mac OS X and all your apps can be kept on the SSD and documents, pictures and other files moved to the larger capacity hard disk. Best iTunes alternative - DMtrans to help you transfer data between computer and iPhone, iPad. DMclone offers reliable and easy solution to help you clone SSD, HDD, USB flash drive or external hard drive. 2 card as my OS drive, and have been cloning itThe best solid-state drives.The best data erasure software to help you permanently shred files, wipe hard drive, erase deleted data beyond the scope of data recovery.Remove the Optical DriveBefore you touch your Mac’s innards, it’s essential that you’re grounded. Remove all the screws holding your Mac together – remember which goes where 2. Once you’ve unscrewed them, you should be able to remove the bottom plate of your computer. Next, unscrew the 10 screws found underneath your MacBook – note that some are longer than others, so it’s important that you remember which ones go where and put them to one side. Open Your MacBefore you open up your Mac and perform open heart surgery, make sure it’s cool – it’s best to wait 10-15 minutes because they can get quite hot. Here each of the file systems that would be supported is HFS+, ext, VMFS3, ext, and more.SSD disk drives have extremely quick access timesA word of caution: it’s recommended that you read up and consult a professional before attempting any hardware upgrades yourself – the upgrade process is difficult so it might be wise to let an expert do it. And don’t forget to make a complete backup with Time Machine or another suitable solution, just in case the worst happens!Lastly, taking apart your MacBook and following the process below will certainly void your warranty, but if you’re not too concerned about this fact then it will probably be the best upgrade you’ll ever do…The MCE OptiBay drive enclosure is an essential item 1.Connect the SSDThe old hard disk is going to sit in the OptiBay where SuperDrive you just removed used to be. The standard optical drive and hard disk layout in a MacBook Pro 3. Next, unscrew the drive from the Mac’s case – it’s advisable to use a magnetic screwdriver, because the screws themselves are notoriously easy to lose inside your Mac. Once you’ve freed the optical drive from the case, remove the SATA plug which is attached to the ribbon cable. The SuperDrive is connected to the motherboard by a small black or red ribbon – just pull this out of the socket before you continue. Remove any cords attached to it (or there may be a small Bluetooth circuit board in the way which has to be removed). Next, load your old drive into the OptiBay housing before you install it into your Mac. Just disconnect the cables and remove any screws. The reason is that if you just leave the old hard disk in the current position and install the SSD in the SuperDrive slot, there will be problems when your Mac wakes from sleep, as it doesn’t expect the SuperDrive slot will be the main drive.Remove your old hard disk as above – it’s a nearly identical process. Lastly, re-attach the bottom panel of your Mac and use the original screws taking careful note of which ones went where. The next step is to connect the SSD to the cables that the old disk drive was using and screw it firmly into place. Use the old SuperDrive screws that you removed earlier to secure the OptiBay onto the motherboard – be careful not to lose any screws in the process. Slide your old hard disk into the OptiBay enclosureNext, connect the SATA ribbon cable that was connected to the SuperDrive to the slot on the side of the OptiBay and put it onto the empty space which was left by the optical drive. Slide it in all the way until it’s secure in the SATA plug on the housing. Once that’s done, continue to the next step. If so, installation was successful, and it now has to be formatted as Mac OS Journaled using the controls in the Erase tab. Open Disk Utility and check that the SSD appears in the sidebar on the left. Click the lock at the bottom left and enter your password to be able to make changes. To do this, open System Preferences and select Users & Groups. When that’s done, just select the Clone button and just wait for it to finish.Next, reboot your Mac and hold down the OPTION key so you can choose the boot disk – select the SSD and watch in awe as your Mac boots quicker than ever before!Next, you need to move some of the application settings from your Home folder onto the SSD. In the Source Disk section deselect the Home Folder checkbox, because your Home Folder will reside on your old hard disk so it should be excluded from the cloning process. Then set the Target Disk to the new SSD which has just been installed. Carbon Copy Cloner is a free app which will help you move Mac OS X to the SSDOn the left side, set the Source Disk to the current boot volume, which is normally called Macintosh HD. Planning center app for macThis will free up loads of space and also makes it non-bootable, so your Mac will default to the SSD when it boots.That’s really all there is to it – saving user files to folders such as Downloads and Documents simply works because you’ve relocated your Home folder. Change the Home directory to point to the correct folder on the old hard diskLastly, go to the old drive and delete everything except the Users folder which is at the very top level. Note that for items such as desktop backgrounds, you may need to set them up again. This process must be repeated for every user on your Mac. Then just log out and back in again. In the Home directory section, hit the Choose button and navigate to the existing Home folder on your old disk. The enclosure connects via USB and should run without problems on USB power, but just case there’s an extra lead and power socket supplied if necessary. To use the drive, just slide a disk into the slot and it’ll automatically be sucked in just like when it was installed in your Mac. Just take apart the black plastic case and connect the chip inside to your SuperDrive’s SATA port, then put the drive in the case and close it. These cookies ensure basic functionalities and security features of the website, anonymously.This cookie is set by GDPR Cookie Consent plugin. So just sit back and enjoy using your new super-fast Mac…Necessary cookies are absolutely essential for the website to function properly. Everything should seem snappier and the boot time will be much quicker. Enjoy an Insanely Fast Mac!Your Mac should now automatically boot from the SSD and all your files and documents will be saved to the old disk drive that was moved to the slot previously occupied by the SuperDrive. It does not store any personal data. The cookie is used to store the user consent for the cookies in the category "Performance".The cookie is set by the GDPR Cookie Consent plugin and is used to store whether or not user has consented to the use of cookies. The cookie is used to store the user consent for the cookies in the category "Other.This cookie is set by GDPR Cookie Consent plugin. The cookies is used to store the user consent for the cookies in the category "Necessary".This cookie is set by GDPR Cookie Consent plugin.
0 Comments
Leave a Reply. |
AuthorTonya ArchivesCategories |